Literature

ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Kazilkree Shaktik
Country: Cambodia
Language: English (Spanish)
Genre: Literature
Published (Last): 4 December 2016
Pages: 63
PDF File Size: 6.55 Mb
ePub File Size: 15.83 Mb
ISBN: 770-2-11887-644-8
Downloads: 13218
Price: Free* [*Free Regsitration Required]
Uploader: Dilkree

ASTM A682 Grade 1074

However, the document shall clearly identify the organization submitting the document. General Requirements for Delivery 4. Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size. When one or more of these elements is speci? NOTE 3—When the camber tolerances shown in Table 8 are not suitable for a particular purpose, cold-rolled strip is sometimes machine straightened.

Two additional samples are secured from each end of the coil from which the original sample was taken. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. This edge is produced when the width tolerance and edge condition are not as exacting as for No.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Strip is classified as product that is 0.

Materials and Manufacture 5. A portion of the coil may be discarded prior to cutting the samples for retest. The material must be adequately protected and correctly identi?

When the amount of vanadium, columbium, or titanium is less than 0. Combining values from the two systems will result in nonconformance with the specification.

  HOWARD BANDY INTRODUCTION TO AMIBROKER PDF

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis. Normal coiling or piling does not provide a 3 Where an ellipsis. NOTE 2—Camber tolerances as shown in the table are for any mm length. In case of dissatisfaction with the results of the test, the manufacturer may make claims for a rehearing. B The sum of copper, nickel, chromium, and molybdenum shall not exceed 0.

Combining values from the two systems will result in nonconformance with the speci? A number in parentheses indicates the year of last reapproval. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not aastm as part of the standard. Dimensions, Mass, and Permissible Variations 9. Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.

This standard has been approved for use by agencies of the Department of Defense. When the maximum z682 limit exceeds 1. This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Within the text, the SI units are shown in brackets. When required, minimum coil weights are subject to negotiation. Originally published as A ast, Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the atsm.

The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Referenced Documents asgm separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  DEATH OF KLINGHOFFER LIBRETTO PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis.

When the amount of copper, nickel, chromium, or molybdenum is less than 0. Rework and Retreatment Conformance to SI tolerances is mandatory when the “M” specification is used.

Thickness Tolerances Plus or Minus, in. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned aetm this standard. Government procurement by the Defense Supply Agency, strip material shall be continuously marked for astmm Within the text, the SI units are shown in brackets. Number of Tests and Retests The strip may be subjected to product analysis by the purchaser either for the purpose of verifying that the chemical composition is within speci?

Within the text, the SI units are shown in brackets. Note 1—The term weight is used when inch-pound units are the standard. Notwithstanding the absence of a628 signature, the organization submitting the document is responsible for the content of the document.

However, under SI the preferred term in mass.